Helping Carbon Art 45 to produce unique stunning sculptures in carbon fibre

Carbon fibre is well known for its high strength-to-weight ratio making it an ideal material for all sorts of applications – from aerospace propellers to prosthetic limbs. Perhaps one of the more surprising applications for the material is sculpture.

Contact us about your carbon fibre finishing requirements

2024 British Grand Prix trophies made in carbon fibre by Carbon Art 45

Case study at a glance

  • Customer: Carbon Art 45, a carbon fibre sculpture studio in Brackley, UK
  • Work: engineering-inspired sculptures and trophies, including the 2024 British Grand Prix trophies
  • Challenge: removing waxy residues from carbon fibre without damaging the fibres, before painting and lacquering
  • Solution: Vapormate compact manual wet blasting machine
  • Result: a clean, ‘wet out’ surface that paint and lacquer spread across evenly, and “a lot of man hours” saved
Vapormatt Vapormate manual wet blasting machine front right view with operator

The challenge: a flawless painted finish on carbon fibre

UK based Carbon Art 45 use carbon fibre to produce some truly stunning engineering inspired pieces. 

Alastair Gibson and his team’s high end engineered sculptures have been exhibited worldwide and include giant squid, human hearts and the incredible trophies for the 2024 British Grand Prix. 

Perfect preparation for the meticulous and beautifully painted and lacquered surfaces is critical to the  sculpting process. 

The company’s Vapormatt Vapormate manual wet blasting machine is ideally suited to the job. The machine cleans carbon fibre, removing waxy residues and other contaminants, without damaging the material’s fibres. In the same operation a ‘wet out’ surface is created that ensures coatings, like paints, lacquers and adhesives, don’t bead up on the surface but instead spread across the surface of the carbon fibre for best possible coverage and subsequent adhesion.

‘Our Vapormate has without a doubt stood the test of time and saves us a lot of man hours. It is also very consistent and reliable.’

Josh Rowland, Carbon Art 45
Carbon Art shark sculpture

Why the Vapormate suits a sculpture studio

The results speak for themselves! Visit the Carbon Art 45 website, carbonart45.com, to see a unique collection of awe-inspiring work. With its compact size, yet large working area, and  manual operation, the Vapormate is the perfect wet blast machine for the company’s highly varied bespoke and low volume work. 

Air pressure control, rinse and dry guns, a wide opening door and a range of other features help ensure Alastair and his team achieve the precise finish required every time. The Vapormate also fits through a standard doorway making it ideal for installation in Carbon Art 45’s studio. 

Visit our composites industry page to learn more about the benefits of wet blasting composites.

Learn more about the Vapormate wet blasting machine.

Download a PDF copy of this case study

 

Contact us

Tell us what you make and how you finish it. A Vapormatt applications engineer will recommend the right machine, media and pressure for your parts.

FAQs

Why does carbon fibre need preparing before painting or lacquering?

Moulded carbon fibre carries waxy release residues and a resin-rich surface layer that repel coatings. Paint and lacquer bead up instead of spreading, which causes patchy coverage and poor adhesion. Wet blasting removes that layer and leaves a surface that coatings wet out across.

Learn more about wet blasting for composites

Does wet blasting damage carbon fibre?

No, not at the recommended pressures. The water cushions the abrasive, so it cleans and lightly profiles the surface without cutting fibres. A Vapormatt applications engineer sets the media and pressure to suit your parts.

Learn more about wet blasting for composites

Is a manual wet blasting machine right for one-off or low-volume work?

Yes. For bespoke pieces of different shapes, a manual machine such as the Vapormate lets the operator adapt the finish to each part. For repeated, higher-volume production, an automatic machine gives recipe-controlled consistency.

Learn more about the Vapormate

Will a Vapormate fit in a small studio or workshop?

Usually, yes. The Vapormate is 735 mm wide, fits through a standard doorway and runs on 220/240 V single-phase power. It needs a compressed air supply of 2–7 bar.

Learn more about the Vapormate